1) First log in to your camera; then, if you are using Internet Explorer, click on the For Administrator tab. If you are using Firefox then click on the Device Management tab.

2) Then Select Mail Service Settings on the left side panel.

3) Here you need to input your SMTP information including username, password and SMTP server. Most ISP’s such as AOL and Roadrunner will provide you with this, however if they do not you will have to seek a 3rd party company to supply you with one. (Note: GMX, Gmail and Hotmail will not work). Then enter the sender and receiver Email address. See below for an example.

4) Click submit before you click test.

5) Now, in order to get your Motion Detection to start working you will need to log into your camera again and goto Alarm Service Settings and check the box for Motion Detect Armed.

Step 1.
Open you web browser. Enter the router IP address in the address bar as shown below, (192.168.2.1), then press Enter.

Step 2
Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.
Click “Submit”
If you have changed it and don’t remember it you may have to reset your device to factory default using the reset button on most routers.
Default username: (admin) and password: (n/a; blank) for Belkin routers.

Step 3
Once logged into your router click on “Firewall”
Once the page has loaded click on “Virtual Servers”

Step 4
First you want to be sure to check “Enable”
In the Description column enter a description of your network device (e.g. Foscam Camera)
In “Inbound port” enter the starting ports to be forwarded.
Example: 2100-2500
Next choose the “Type” you want to use. (For Foscam cameras we will use TCP)
Enter the Camera’s P address in “Private IP Address”
In “Private port” enter the ending ports to be forwarded.
Example: 2100-2500 (note: Inbound and outbound ports are the same)
Repeat step 5 for any more ports you want to forward.
Click on “Apply Changes”

Step 5
To view the camera over the internet enter you router external ip address which can be found by typing www.whatismyipaddres.com into your browser.

Enter the Ip address 24.76.212.746: port for the camera (e.g. port 8090)
24.76.212.746:8090 is what should be typed into you browser.

Step 1
Open your web browser. Enter the router IP address in the address bar as shown below,
(192.168.0.1) followed by pressing Enter.

Step 2
Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here.Then click “Log In”
If you have changed it and don’t remember it you may have to reset your device to factory default using the reset button on most routers.
If you don’t know it you can check the user manual for your router.

Step 3
Select the Advanced Tab

Step 4
Select “Virtual Server” on the left hand side of the page

Step 5

Enable the system by checking the enabled box

In the Private IP enter the cameras local IP address (192.168…)

In the Protocol field, select TCP.

In the Private port enter the port number you need to port forward (e.g. 5000)

In the Public port re-enter the port number you entered in the private port field (e.g. 5000)

Select the Schedule to Always

If more ports are required to be port forwarded, repeat the above steps. When complete, selectthe Apply button located at the bottom of the page to save your changes.

Step 6
To view the camera over the internet enter you router external ip address which can be found by typing www.whatismyipaddres.com into your browser.

Enter the Ip address 24.76.212.746: port for the camera (e.g. port 8090)

24.76.212.746:8090 is what should be typed into you browser.

Step 1:
Open your web browser.
Enter the router IP address 192.168.1.254 in the address bar as shown below, followed by pressing
Enter.

Step 2
Once logged into your router click on the “Firewall” tab on the top right.

Step 3
Click on “Firewall Settings”.
Once the page is loaded click on ‘Add a new user-defined application’.

Step 4
For ‘Application Name’ give this entry a name e.g. Foscam Camera
For ‘Protocol’ Choose ‘TCP’
For ‘Port (or Range)’ in ‘From’ & ‘To’ enter the ports to be forwarded.
Example: 8090 to 8090
For ‘Protocol Timeout (seconds)’ & ‘Map to Host Port’ & ‘Application Type’ you can leave these all at their default values.
Click ‘Add Definition’
Repeat this step for all ports.
Once you have entered all the ports for this entry click ‘Back’

Step 5
For ‘Select a computer’ choose the Foscam Camera’sIP address to forward the ports to.
Choose ‘Allow individual applications’
Choose ‘User-defined’ from the drop down box
In the list on the left choose the entry you created “Foscam Camera” and then click ‘Add’
Repeat this step for each entry you need to add.
Once you are all done click ‘Done’

Step 6
Once you’ve done that, Foscam Camera should appear in the Hosted Applications
Click the Done button at the bottom right corner of the screen, and you should see the following screen:

Step 7
To view the camera over the internet enter you router external IP address which can be found by typing www.whatismyipaddres.com into your browser.

Enter this IP address 24.76.212.746: port for the camera (e.g. port 8090)
24.76.212.746:8090 is what should be typed into you browser.

Step 1
Open your web browser.
Enter the router IP address 192.168.0.1 in the address bar as shown below, followed by pressing
Enter.

Step 2
Some router/modems require a username and/or password, if yours requires it, enter the routers username and password here. Then click “Log In”
If you have changed it and don’t remember it you may have to reset your device to factory default using the reset button on most routers.
If you don’t know it you can check the user manual for your router.

Step 3
Click “Port Forwarding/Port Triggering” on the left side menu

Step 4
Click Add Custom Service

Step 5
First give your camera a name under “Service Name”e.g Foscam Cam
Next select Service Type as TCP
Next for “Starting Port” enter in the starting port you would like to forward. E.g.8090
For “Ending Port” enter in the ending port you would like to forward. E.g. 8090
Enter the camera’s IP address in “Server IP Address”
Click on “Apply”

Step 6
To view the camera over the internet enter you router external IP address which can be found by typing www.whatismyipaddres.com into your browser.

Enter this IP address 24.76.212.746: port for the camera (e.g. port 8090)
24.76.212.746:8090 is what should be typed into you browser.